NOTHING STICKS BUT THE SHINE!®
RejeX is a water-clear, thin film polymer coating designed to provide an ultra-high-release surface. RejeX is commonly used as a paint sealant providing a high-performance alternative to conventional wax-based products to maximize protection and shine on vehicles of all sorts, including aircraft, cars, motorcycles, boats and RVs.
This very thin film, only tenths of a micron thick, reduces adhesion of all common contaminants such as road grime, exhaust, oil, bug splats, bird droppings, brake dust, tree sap, pollen, tar and grease. RejeX provides the best UV protection of any product of its kind. RejeX is even effective against the dreaded love bugs! It can also be applied to windshields (glass, Lexan, acrylic, etc.) to repel rain and make bugs splats easier to remove. RejeX produces a deep, lustrous shine that outlasts other "wax" products by months.
RejeX contains none of the free silicone oils found in some other polymer products that are known to contaminate paint and cause issues when repainting.
When ambient temperatures are above 85° F, RejeX should be applied out of direct sunlight. If the surface is too hot, the coating will dry before it has properly bonded to the surface, and it wont last to its full potential. If the surface becomes hot to the touch, cool by rinsing liberally with wate, dry, then apply RejeX. For larger vehicles such as RVs, busses and yachts, a good trick for dealing with hot days is to apply RejeX to the top and western facing side in the morning and the eastern facing side in the afternoon, so that you're always working on the shady side.
RejeX should be wiped on, allowed to dry for 10-20 minutes until it forms a haze, wiped off, then allowed to cure for 8-12 hours (depending on the humidity). The higher the humidity, the faster RejeX cures.
When applied, the RejeX monomers (polymer building blocks) attach to the surface being treated and polymerize (cross-link) into a crystal-clear, flexible, chemically resistant film. It is very important to allow RejeX to cure for 8-12 hours after the haze has been wiped off. If the coating is exposed to contamination such as oil, fuel, soot, water, cleaners, etc. before it has cured, the contaminants may interfere with the structural integrity of the film, affecting its visual characteristics and release properties.
|Cure Time||0 hours||4 hours||12hours||24 hours|
|Detergent Wash Cycle Rating||6||16||25||32|
REJEX PROTECTS AND BEAUTIFIES SMOOTH PAINTED SURFACES, GLASS, ACRYLIC, GELCOAT / FIBERGLASS, GLOSSY PLASTIC & POLISHED METAL, STONE AND SYNTHETIC SURFACES
RejeX is not meant to be used on porous surfaces or highly oxidized painted surfaces. RejeX can be applied in multiple coats – allowing at least 4 hours curing time between coats – for greater depth of gloss. RejeX has a higher refractive index than any wax, so it produces richer, deeper looking colors and a lustrous long-lasting finish. It is especially notable on dark colors and metallic paints where RejeX brings out the accurate color and detail in the paint.
RejeX can be used over existing wax, however, the duration of protection will be reduced as the softer underlying wax degrades comparatively quickly. Waxes can be applied over RejeX, however many of the benefits of RejeX will be negated and the wax finish will not last very long due to adhesion limitations. It should also be noted that many waxes and all polishes contain abrasives, which can strip the thin RejeX film.
If a RejeX-treated surface needs repainting, normal paint preparation is all thats required. Abrasive cleaners, polishes, rubbing compounds or chemical paint strippers will remove the RejeX film.
INSTRUCTIONS FOR USING REJEX
Shake well and apply to a clean, dry surface that is cool to the touch. Do not apply in direct sunlight when ambient temperatures are greater than 85° F. On hot days, we recommend RejeXing in the shade, early morning or in the afternoon.
After RejeX dries to a haze (about 10-20 minutes), simply wipe it off. Unlike waxes that require strenuous rubbing or buffing to remove, RejeX wipes on and off easily. Buffers work just fine. If you use a buffer, do not apply RejeX with pressure, simply use the buffer to spread out (and/or wipe off) the product.
Allow RejeX to cure for 8-12 hours out of the elements.
For optimum protection, reapply every 6 months as needed.
For the perfect pre-cleaner for RejeX, check out our new product Xtreme Clean
has recently been awarded the GSA National Stock Number 8030-01-593-8208 for use on all NATO destroyers and cruisers armed with the AEGIS defense system.
in convenient 12 oz., 16 oz.
and 1 gallon containers
12 oz. - $14.95
16 oz. - $19.95
1 gallon - $129.95